Mooring Chain Check-up at 12 Months

Seven different types of links-including five galvanized chains, one zinc-plated chain, and one stainless chain-were dropped in the drink a year ago. Testers raised them from the depths to see how well they fared in the chain corrosion test.

0

Practical Sailors 12-month results in the mooring chain test gave us no reason to change our previous ratings. Our vote still is for the Acco grade-30 proof coil. Its the best chain for the dollar. If youre made of money, you could set up your mooring with the Suncor stainless. But the dark side of stainless is that after years of cyclical loading, it can break without warning. Corrosion is just one of the factors affecting a chains integrity, and until we start putting these chains under load, and ultimately, testing them for breaking strength, many questions will remain unanswered.

                                                    ****

Mooring Chain Test

Some Practical Sailor tests go on and on. And on. Back in November 2005, we put seven 5-foot lengths of 5/16-inch chain into Long Island Sound, in an area known to chew up chain in short order. Generally, owners of boats on moorings there need to replace the top sections of their chain&emdash;the parts mostly suspended in the water between the heavier, protected chain and the mooring ball&emdash;every three seasons, and sometimes more often. (The test set-up was initially described in the March 2006 issue and updated in the September 2006 issue.)

After six months, we pulled the chains out for a look. The six-month ratings are shown in the accompanying chart.

The chains were then moved from an area of more current and chop (and also high summer traffic) to the end of a private dock in a somewhat quieter cove. This time, they were suspended in individual loops and hung so that the bottoms of the loops rested in mud and the upper ends in shallow water, exposed to a lot of tide, occasional wave action, and, depending on the moon, air. They were pulled at the beginning of December 2006.

OBSERVATIONS AT 1 YEAR

 

Mooring Chain Test

What we found, predictably enough, was fouling and rust. We put no load on the chains, and didnt expect to see much loss of material; however, once we busted off some of the barnacles, we did find a more pronounced loss in the Campbell and Chinese proof coil specimens. As we noted in earlier articles, these two chains appeared identical initially, and they fared about the same in the six-month review. At 12 months, we could give a slight nod to the Campbell, which looks marginally better than the Chinese, but really, given the vagaries of real-world testing, the informality of judgment, and the possibility that they are, in fact, different brandings of the same chain, the difference isn’t enough to split the ratings. They both get the same as last time: Fair.

The three Acco chains and the Campbell zinc-plated chain also maintain the same Good ratings. The surprise here is the Campbell zinc-plated chain. Although the plating is now all gone, the steel underneath is well-preserved. Its not quite as robust as any of the Accos, but its better than its Campbell cousin or the Chinese chain.

Since these ratings are relative, we can elevate the Suncor stainless from Good to Excellent. At the six-month review, we noted that the chain was strong and clean, but we worried whether discoloration at the welds would develop into corrosion. At 12 months, the answer is no. The Suncor looks just about perfect. Maybe one of our metallurgical subscribers can comment.

As for a recommendation, we see no reason to change chain choices. Our vote would still be for the straight Acco grade-30 proof coil. Its the best chain for the dollar. If youre made of money, or keep a really small boat in really shallow water, you could set up your mooring with the Suncor stainless. But the dark side of stainless is that after years cyclical loading, it can break without warning.

Our test so far is not putting the chains under load, so no work hardening is occurring. Corrosion is just one of the factors affecting a chains integrity, and until we start putting these chains under load, and ultimately, testing them for breaking strength, many questions will remain unanswered. With stainless steel in particular, disregarding work hardening under real mooring and anchoring loads involves a serious leap of faith (see “Marine Metals,” February 2007). Stainless steel sees so little use in high-load-cycle applications precisely because it does not hold up as well to this use as materials with higher ferrous content. Its ever-shiney surface can actually be a disadvantage, revealing no clues to impending failure.

THE NEXT DUNK

The chains spent the cold winter months lying in a bed of mud and ice. This spring, they were strung together and slightly twisted into a sort of chain skein, and hung overboard, completely out of the mud, but more often in the air. In order to induce some extra stress, weve passed the chain skein through a cinderblock, which weighs down the skein as the tide falls. To oppose that, weve attached a Taylor-Made buoy to the cinderblock. Well report again in the fall.

Darrell Nicholson
Practical Sailor has been independently testing and reporting on sailboats and sailing gear for more than 50 years. Supported entirely by subscribers, Practical Sailor accepts no advertising. Its independent tests are carried out by experienced sailors and marine industry professionals dedicated to providing objective evaluation and reporting about boats, gear, and the skills required to cross oceans. Practical Sailor is edited by Darrell Nicholson, a long-time liveaboard sailor and trans-Pacific cruiser who has been director of Belvoir Media Group's marine division since 2005. He holds a U.S. Coast Guard 100-ton Master license, has logged tens of thousands of miles in three oceans, and has skippered everything from pilot boats to day charter cats. His weekly blog Inside Practical Sailor offers an inside look at current research and gear tests at Practical Sailor, while his award-winning column,"Rhumb Lines," tracks boating trends and reflects upon the sailing life. He sails a Sparkman & Stephens-designed Yankee 30 out of St. Petersburg, Florida. You can reach him by email at practicalsailor@belvoir.com.