Boat Maintenance

In response to your request regarding safety tether knowledge or suggestions (see Safety Tether Warning, Inside Practical Sailor) please test and include information about Glowfasts HLR Safety Line system.

I have a West Marine Watertender 9.4 with a polyethylene hull (versus polypropylene for the Walker Bays) and am wondering if there is an anti-fouling paint that is suitable. Looking through the product info for both, the manufacturers both claim that the plastics are slippery enough to not need paint, however, the plastic wrap (unknown material) on the wooden pilings on my own docks in Florida have marine growth on them, so I suspect the same will happen with my Watertender (currently stored on the dock).There are conflicting reports/opinions on various forums as to if there is a paint that would actually stick to the hull, as well as potentially damage the plastic.

Multifunction display manufacturers have pushed their products through a dramatic evolution in the last five years as they try to keep pace with technology that we take for granted in our other electronics. Better interfaces, screen resolution, and the ability to download useful software apps (beyond navigation) are just some of the improvements. Most of the major vendors are on their third generation of touchscreen interfaces, higher resolution displays, downloadable software, remote music control, and other functions far afield of what MFDs performed five years ago.

For more than 20 years, I always had bow-mounted vanes-a Telo Cat on my beach cat and a Windex sport on my Stiletto 27. The Telo Cat was sheltered under the forestay bridle and bowsprit and was never damaged. The long bows of the Stiletto kept the Windex out of harms way-although the Stiletto had a spinnaker, it reached faster than the wind and we always tacked downwind, jibing the chute inside like a jib and keeping the sail and sheets away from the bows. When I moved on to a PDQ32 catamaran, a cruising cat with a chute that is jibed outside, there was no place where either a sail or sheet couldnt pulverize the vane in short order. I learned this the hard way, crumpling several commercial vanes. The solution was not to build something strong, but rather to build something that could flex with the assault and pop back up; a flexible wand topped with a length of yarn.

Insulation is a greater energy-saving expedient; if our heater or air conditioner is undersized, fixing drafts, shading or insulating windows, and insulating non-cored laminate are all ways to reduce the thermal load. For boaters, however, that is only half of the equation.

Spider cracks can indicate impact damage or serious structural problems that will need to be addressed to prevent spreading, but most often they result from relatively inflexible gelcoat that is too thick. Stress by thermal expansion or when bulkheads and liners were installed can cause minor flexing. Cracks from larger issues-a winch, for example, that was inadequately mounted-will need to be fixed before cosmetic repairs begin.

Im trying to determine the cause of erosion of the centerboard pivot pin from Arcturus, our 36-foot Soverel keel/centerboard cutter. It is a -inch diameter silicon bronze pin installed new in 2004. I removed the centerboard a few weeks ago and was surprised to see that the pin was heavily corroded. Ive attached a few pictures of the pin. The boat has a fiberglass encapsulated lead keel, with the lead bedded in a resin/sand mixture. The pivot pin fits in a hole drilled through the keel and centerboard trunk (which has encapsulated lead on both sides).

Sunbrella does not shrink. That is the mantra, and for covers and dodger that are left in place, it seems to be the true. It stretches a little when wet, and so long as it is maintained under tension while it dries, it retains it shape. So says Sunbrella. While this seems true for tensioned cloth (our dodger still fits) and it hardly matters for a sail cover, our real world experience with removable Sunbrella window covers has been different, shrinking as much as 5 percent over a period of years. The problem, no doubt, is that these are worst case scenario, repeatedly removed while still wet with dew and allowed to dry. The end result was that the covers became difficult to install and some of the snaps were being ripped out by the excessive tension.

Insulation is a greater energy-saving expedient; if our heater or air conditioner is undersized, fixing drafts, shading or insulating windows, and insulating non-cored laminate are all ways to reduce the thermal load. For boaters, however, that is only half of the equation.

Depending on the collection area and the sailing, salt can be a primary problem. Spray falls and dries, layer after layer, until the decks hold enough salt to foul a considerable flow of water. The solution? Wash the deck with seawater before the rain comes. Squeegee off as much as practical or towel dry, and common sense dictates this is best done when at sea and must be done away from red tides. We tested the run-off from the top after scrubbing with seawater, allowing to dry, and then spraying with tap water equivalent to 1/10-inch of rain (see results in table below). In addition to taste, seawater contains significant sulfate levels, which combined with bacteria in the tank under anaerobic conditions, can lead to sulfurous water; sailors notice this when a seawater flush is used for the head, but allowed to become stagnant for a few days; the first flush will smell.